ICDO Buy ICDO Gear at the ICDO CafePress Store!
Toggle Content Toggle Content
 
  Toggle Content
Menu:
 

  Toggle Content
User Info
 

Welcome Anonymous

Nickname
Password

Membership:
Latest: KillNThrill24
New Today: 0
New Yesterday: 0
Overall: 7879

People Online:
Members: 0
Visitors: 32
Total: 32
Who Is Where:
 Visitors:
01: Home
02: Photo Gallery
03: Forums
04: Photo Gallery
05: Forums
06: Forums
07: Forums
08: Forums
09: Forums
10: Forums
11: Forums
12: Forums
13: Forums
14: Forums
15: Forums
16: Forums
17: Forums
18: Forums
19: Photo Gallery
20: Forums
21: Forums
22: Forums
23: Forums
24: Home
25: Forums
26: Forums
27: Forums
28: Forums
29: Forums
30: Forums
31: Forums
32: Forums

Staff Online:

No staff members are online!

  Toggle Content
Donations
 
Donate and suport ICDO!

 
Forums › Marker Talk › Problem/Tech forum :: Archives › miscalculation/ defect in a b2k4???? :: Archived

miscalculation/ defect in a b2k4????
Have a problem with your marker? Ask here
Go to page 1, 2  Next
Post new topic   Revive this topic   Printer Friendly Page     Forum IndexProblem/Tech forum
View previous topic :: View next topic  
Author Message
junior24
Rookie
Rookie


Joined: May 22, 2008
Posts: 28
Location: Jax, FL

PostPosted: Thu Aug 21, 2008 8:53 am    Post subject: miscalculation/ defect in a b2k4????

I picked up a b2k4 for $60 and I was told it was due to a miscalculation from manufacturer that causes it to not fully cycle. So I messed with the regulators and it operates, just when I put paint in it. It can barely spit the paint out....
need help????
Back to top
View user's profile
ssechriest
ICDO Supporter
ICDO Supporter


Joined: May 01, 2007
Posts: 1430
Location: Virginia

PostPosted: Thu Aug 21, 2008 9:53 am    Post subject: Re: miscalculation/ defect in a b2k4????

Bolt hole not facing down?

valve not opening all the way?

messed up hpr?

I was watching this one on ebay as well. I am sure you got a good deal, with a fixable problem. But, without having it to look at... its hard to diagnose. Does it cycle smoothly without paint? Without it being aired-up, the bolt should be able to slide back and forth easily, and stop when it gets to the valve stem. You should be able to push it forward to push the valve open. what is you hpr pressure? you balanced the regs IAW the SOP?
Back to top
View user's profile
junior24
Rookie
Rookie


Joined: May 22, 2008
Posts: 28
Location: Jax, FL

PostPosted: Thu Aug 21, 2008 12:15 pm    Post subject: Re: miscalculation/ defect in a b2k4????

Thats the one . When I first got it bolt pin wasn't in right and the hpr adj screw was cross threaded in the close position so no air was getting passed it replaced with an old Bushmaster hpr works cycles smooth, bolts in correctly. hp is at 300.
Back to top
View user's profile
ssechriest
ICDO Supporter
ICDO Supporter


Joined: May 01, 2007
Posts: 1430
Location: Virginia

PostPosted: Thu Aug 21, 2008 12:26 pm    Post subject: Re: miscalculation/ defect in a b2k4????

Drop hp down to 200 or so. Make sure the bolt is in with the large hole facing down. turn up the lp about half a turn to see if it makes a difference... try these things, then...

Cant really check the valve without taking some stuff apart. Maybe you can pull out the bolt and feel for air coming into the upper tube through the hole just behind where the feedneck threads in.

Since you have 300 psi in the HP air side, then you have either a bolt problem (upside down), or the valve is not opening (stuck, lp not enough to force it open), or the valve is in wrong (with the hole turned so that it is not facing to the upper tube, or in backwards so the large hole is facing the back of the gun...).... any other ideas???
Back to top
View user's profile
TheArtist
Amateur
Amateur


Joined: Apr 11, 2005
Posts: 223
Location: Dell Rapids SD

PostPosted: Thu Aug 21, 2008 2:58 pm    Post subject: Re: miscalculation/ defect in a b2k4????

pull the top bolt out and look at the ram head, if you see threads it has come loose. This will cause the problems you described, I Have seen it on many promasters.
Back to top
View user's profile Visit poster's website
junior24
Rookie
Rookie


Joined: May 22, 2008
Posts: 28
Location: Jax, FL

PostPosted: Thu Aug 21, 2008 3:42 pm    Post subject: Re: miscalculation/ defect in a b2k4????

thanks, i'll try it all. also i've pulled out the bolt and dried fired it, the ram doesn't seem like its hitting the valve. If the valve is stuck then how does the marker cock itself. thanks for all your guys help.
Back to top
View user's profile
ssechriest
ICDO Supporter
ICDO Supporter


Joined: May 01, 2007
Posts: 1430
Location: Virginia

PostPosted: Thu Aug 21, 2008 5:08 pm    Post subject: Re: miscalculation/ defect in a b2k4????

These are not blow-back markers. The ram is controlled by a solenoid valve in the tray under the body.

I think if you up the low pressure and it may fire fine.

I assume you are new to bushies. In that case, welcome. there is some good info in the ICDU section, in the upper left corner of your screen. And i hate to say it, but there is a good selection of info over on PBN as well.
Back to top
View user's profile
junior24
Rookie
Rookie


Joined: May 22, 2008
Posts: 28
Location: Jax, FL

PostPosted: Fri Aug 22, 2008 10:51 am    Post subject: Re: miscalculation/ defect in a b2k4????

thanks, and I am new to the family, but this is my sec bushy but that was an easy fix...
Back to top
View user's profile
ssechriest
ICDO Supporter
ICDO Supporter


Joined: May 01, 2007
Posts: 1430
Location: Virginia

PostPosted: Fri Aug 22, 2008 11:28 am    Post subject: Re: miscalculation/ defect in a b2k4????

Is it working now?
Back to top
View user's profile
junior24
Rookie
Rookie


Joined: May 22, 2008
Posts: 28
Location: Jax, FL

PostPosted: Fri Aug 22, 2008 12:47 pm    Post subject: Re: miscalculation/ defect in a b2k4????

lpr in all the way same thing. could it be the lpr or valve
Back to top
View user's profile
Display posts from previous:   
Post new topic   Revive this topic   Printer Friendly Page     Forum IndexProblem/Tech forum All times are GMT - 7 Hours
Go to page 1, 2  Next
Page 1 of 2


Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum
 

 
Photo Gallery Pics...
Toggle Content

Forums scroll Last posts
Toggle Content
Last 10 Forum Messages

Sloppy stock trigger
Last post by Nobody in Bushmaster General talk on Jun 28, 2017 at 23:45:36

Lube valve stem?
Last post by Nobody in ProMaster on Jun 27, 2017 at 18:22:11

Looking to buy or trade for a T2 Frame
Last post by BrandonM816 in ICD Gear Forum on Jun 25, 2017 at 11:16:26

Nox Boards
Last post by BrandonM816 in ICD Gear Forum on Jun 24, 2017 at 21:22:06

Just Got In
Last post by 63VDub in Paintball talk on Jun 14, 2017 at 00:45:05

Good to see people still here.
Last post by ogti9g9 in Off Topic on Jun 09, 2017 at 19:47:47

Modded 02 BKO
Last post by ogti9g9 in Appraisals on Jun 09, 2017 at 19:46:12

Noid Question...safe to air up?
Last post by Fuzzyfoot3789 in ProMaster on Jun 09, 2017 at 13:01:45

Anyone Has Tried Using Bark Collars?
Last post by Nobody in Off Topic on Jun 07, 2017 at 20:35:40

Wondering what to do this weekend?
Last post by Nobody in Off Topic on Jun 07, 2017 at 20:30:39


 
All info copyright www.icd-owners.com 2000-2016. No reproduction of anything on this site is permitted without express consent from ICDO.
Interactive software released under GNU GPL, Code Credits, Privacy Policy